:::::: New Products ::::::

BULLITPRUF’S NEW TWIN ROTOR THROTTLE BODY

BULLITPRUF’S NEW TWIN ROTOR
THROTTLE BODY
45-6.jpg

 

Bulitpruf’s new Twin Rotor Throttle body is a radical
departure from any throttle on the market today. It has no plates or shafts to
restrict airflow, in fact there is no restrictions at all at full throttle. The
throttle bodies come in two sizes. The small one fits a standard 4150 carb base
and flows 2100 CFM @ 28 in. The large one fits a standard 4500 carb base and
flows 3500 CFM @ 28 in. Throttle response is smooth and progressive. It can be
used for either EFI or mechanical fuel injection. It comes with a standard top
as shown or a top incorporating a built in tray for a GOZO air scoop or a
Bulitpruf designed air scoop.

 
In dyno tests conducted with Edelbrock 
and Pat Musi our 4500 throttle out performed   all throttles tested during a two day test
session including Ron’s. It picked up 32 HP and 27 ft/lb of torque on a 1037 Hp
engine over the best. The engine was a 555 Chevy with EFI on gas.

For more information call Bulitpruf at 
888 997 7816 or our web at www.bulitpruf.com

Precision-Flow Fuel Injectors

New FAST™ injectors feature
highest flow rate of any injector specifically designed for 2005-2008 LS2 / LS7
/ L76 / L92 engines
lsfuelinjectors.jpg

The
FAST™ Precision-Flow™ Fuel Injectors for GM Gen IV engines are the highest
flowing injectors available and are uniquely designed for direct installation
into LS2 and LS7 / L76 / L92-style engines. Available in two different height
configurations and a wide range of flow rates, the new Precision-Flow™ Fuel
Injectors are correctly sized (shorter than the common LS1/LS6 injectors) and
feature the right EV6/UScar connector, enabling hassle-free plug-in operation.
In addition, the high-impedance, high-flow FAST™ injectors meet/exceed all
factory durability standards and quality tolerances.

Prior
to the arrival of Precision-Flow™ Fuel Injectors for GM Gen IV engines,
performance engine builders were required to retro-fit high-flow Gen III
(LS1/LS6) injectors which required a wiring harness adapter to fire the
injectors. Most importantly, due to the fact that LS2 and LS7 engines feature
shorter fuel injectors than other LS engines, when performance injectors were
required engine builders would have to modify the fuel rail placement to fit the
Gen III (LS1/LS6) style injectors. The new FAST™ Precision-Flow™ Injectors for
GM Gen IV engines are simple drop-in components offered in fuel rates up to 57
lb/hr (LS2–type) & 65 lb/hr (LS7/L76/L92-type), the highest rate currently
available for GM Gen IV engines. For more information about the FAST™
Precision-Flow™ Fuel Injectors for GM Gen IV engines or any other FAST™ product,
call us at 1-877-334-8355, or visit us online at www.fuelairspark.com.

Flatout Gaskets - Big Block Chrysler oil pan gasket

Flatout Gaskets is pleased to announce the release of their exciting new product
for Big Block & Hemi Mopars. After months of extensive
testing, clip_image004.jpgFlatout has developed a silicone rubber/steel carrier oil pan gasket
that out-performs all others!

 

Part #5020, Big Block Chrysler oil pan gasket is now
available.

 clip_image006.jpg

The “ALL SEASON™”
steel carrier
based product uses the latest in rubber molding technology to offer the
racer/builder a quality product that is not only re-useable, but also does not
stick to the block & pan surfaces.  Flatout has also incorporated compression
limiters in all the bolt holes to control the amount of torque on each
fastener!

 clip_image008.jpg

For more
information, please call Flatout Toll-Free @ 877.837.9200 or take a
look at the new on-line product listings at: www.flatoutgroup.com. Flatout products are also
available at www.summitracing.com & www.motorstate.com
.

 

Flatout
Gaskets will be at the 2007 PRI Tradeshow – Dec. 6- 8 in
Orlando, FL. - Booth
#3334. To “STAY SEALED™” stop
by and pick-up a new catalog and learn about all the new sealing products
available from Flatout Gaskets!

  

 

 

 

 

 

 

 

 

 

 

 

 

 

            

COMP Cams GM ZZ4 Power Packages

COMP
Cams® and RHS™ join forces to eliminate the “performance dysfunction” that
plagues GM ZZ4 crate engine owners
zz4.jpg

GM’s
ZZ4 engine has great performance potential straight out of the crate; but in
today’s realm of high performance engines, 350 hp is not exactly something you
brag to your buddies about.  COMP Cams® is dedicated to producing top quality
components that draw the most power and torque from any engine platform. As a
result of this effort, COMP has designed bolt-on GM ZZ4 power packages that
dramatically improve the horsepower, torque and “fun factor” associated with
this engine.

Test
results prove that carefully selected combinations of COMP Performance Group™
products can provide your ZZ4 with extra 16–92 horsepower, as well as bullet
proof reliability. For complete details on the COMP Cams® GM ZZ4 Performance
Packages, including dyno graphs, pictures and part numbers, call us at
1-800-999-0853, or visit us online at www.compcams.com.

COMP Cams Embroidered Dri Mesh Polo Shirts

comp-polo-pr.jpgHigh-quality, comfortable Dri Mesh fabric looks great and keeps you cool under pressure

Keep cool with these red-hot Dri Mesh Polo Shirts from COMP Cams®. The
same shirts worn by their own personnel in the field, COMP Cams® Dri
Mesh Polo Shirts provide the driest moisture wicking protection
available to keep you cool, regardless of the weather. Best of all,
these shirts feature a full color, high-quality embroidered COMP Cams®
logo stitched on the left chest for years of quality appearance.

Available in sizes M-XXL and in white, black or gray, COMP Cams®
Embroidered Dri Mesh Shirts are made from 100% double poly mesh that
stands up to repeated washings without fading. These shirts require no
ironing and look great straight out of the suitcase – an important
feature for traveling racers and performance enthusiasts.

For more information about the COMP Cams® Embroidered Dri Mesh Polo
Shirts or any other COMP Cams® product, call us at 1-800-999-0853, or
visit us online at www.compcams.com

LS2 Power Upgrade with Professional Products New Typhoon Intake

Performance enthusiasts are always searching for more power from their
LS2, and this hot new Professional Products Typhoon intake manifold can
deliver that additional power!

ls2_intake.jpgThe
LS2 Typhoon manifold comes standard with a 96mm inlet opening that will
accept the stock, or any other aftermarket throttle body, including
Professional Products 96mm or 101mm. This manifold can easily be ported
to accept the larger 101mm bore. These throttle bodies will be
available in late 2007.

The Typhoon manifold comes complete with fuel rail kit, stainless
braided crossover hose and the necessary hose and fittings to connect
to the stock GM fuel inlet line. It is also equipped with nitrous
bosses for those enthusiasts who want to install a nitrous system for
even more power! Professional Products provides the intake gaskets,
manifold bolts, stainless mounting brackets and hardware for the fuel
rail kit. The Typhoon is available in either polished #52062 or satin
#52063 finishes.

For more information on Professional Products complete line of
performance intake products, or to download the 2007 Catalog in PDF
format, visit www.professional-products.com or contact Professional Products, 12705 S. Van Ness Ave., Hawthorne, CA. 90250. 323-779-2020 Fax: 323-754-1141.

RAM Clutches Introduces New Pro Mod Clutch Assembly

11_billet.jpgRAM Clutches is proud to introduce new 11-inch Billet Clutch assembly. 

The unit is configured around a nine-stand drive platform with six levers and adjustable static pressure springs. 

The clutch is ideally suited for supercharged Pro Mod and Outlaw
applications and is available in both two and three-disc configurations
for legal and outlaw combinations. 

RAM Clutches has been producing top-of-the-line products for the drag
racing industry since 1972.  Current IHRA World Champions Quain Stott
and Pete Berner rely on RAM Clutches! 

For more information on RAM products visit ramclutches.com or call 803.788.6034 x 201.

All Weather Vehicle Protection From Covercraft

car_covers.jpgThe
most popular fabric used to create Covercraft’s custom fit vehicle
covers is called EVOLUTION®. That popularity is due to its versatility,
providing excellent protection in both indoor and outdoor situations.
Manufactured in the USA by Kimberly-Clark, EVOLUTION® carries their
highest UPF rating against harmful UV rays, and can stand up to the
worst Mother Nature dishes out! Plus, the four-layer thickness absorbs
impacts, helping to protect against nicks, chips, scratches and dents.
The outer layer color is available in Blue, Gray or Tan.

EVOLUTION® is made from Polypropylene fibers bonded into the four-layer
non-woven finish, providing both softness and strength, with a soft
inner liner against your paint. This multi-layer design provides not
only protection against seriously inclement weather, but also from tree
sap, bird droppings and industrial pollutants like acid rain. It’s a
material suit of armor that breathes, allowing moisture, condensation
and heat to escape, while supplying maximum UV protection for your
paint and interior. Covercraft has manufactured EVOLUTION® covers for
over 25-years, and there are more than 1-million covers in use around
the world. All Covercraft’s vehicle protection and convenience products
can be found at www.covercraft.com.

For additional information contact Covercraft Industries, 100
Enterprise Boulevard, Pauls Valley, OK 73075, 800-426-8377, In OK
405-238-9651, Fax: 405-238-9601

New G2/S&S Cycle 126" Engine

126_engine.jpgWhat
do you get when you combine the craftsmanship of S&S Cycle and the
innovation of G Squared Motorsports?  Something POWERFUL & FAST!

Dyno runs have the 126 making over 150 rear wheel horsepower & it
delivers the most torque of any engine in its class – over 145 ft. lbs.

These 4-3/8” bore engines have similar general specifications to the
original S&S Tribute 145 engines, but the new G Squared 126 is a
dual cam design combined with big valve B2 heads for ultimate
performance.  

For the rider who tours from sunup to sundown, the 126 delivers the
massive horsepower you crave, in an engine that bolts directly into
most stock chassis from 1999 and up, and is available with fuel
injection or an S&S carburetor.

The 126 is offered solely through G2 Motorsports and its dealer network and are NOW IN STOCK. 

Be one of the first to step up to 126 POWER.  You’ll be glad you did!
 
Also available in 145 cu. in. version
 
For more information contact: Derek at 229-924-0031 or email [email protected]

L92 Shaft Rockers from JESEL

jesel_rockers.jpgLS
motor enthusiasts are going crazy over GMs' L92 cylinder heads that
offer huge flow numbers at an extremely reasonable price. The only
component lacking for the L92 head was a race-ready performance
valvetrain. JESEL solved that problem with a sophisticated shaft rocker
system that is capable of delivering more power due to greatly reducing
valvetrain friction, and providing rock-steady valvetrain stability at
extreme rpm.

Much of the friction reduction is due to the 1.400” pivot length that
reduces “scrub” between the rocker and valve tip. The rockers ride on
precision needle bearings plus a .250”-wide needle bearing nose roller
ensure smooth rocker action throughout the lift curve. Other standard
features include JESEL’s proprietary 7000 series alloy rocker bodies
CNC machined to JESEL’s exclusive Mohawk shape that provides the
lightest and stiffest rocker possible. The rocker bodies also featured
profiled tail sections for valve cover clearance and are shotpeened for
added strength.

There is a choice of rocker ratios from 1.65-1.90, and tool steel
pushrod cup adjusters are also standard. Optional ball adjusters are
available for reduced friction and to add even more strength to the
rocker body (another JESEL innovation). ARP hardware anchors the
one-piece billet steel stands and centerless-ground shaft assemblies.

Installation is a simple bolt-on operation with no cylinder head
machining required. However, taller valve covers or valve cover spacers
are required for adequate clearance. For more information please
contact JESEL at 1985 Cedarbridge Ave., Lakewood, NJ 08701. Phone
732-901-1800. Fax 732-901-6777. Or visit us on the web at www.jesel.com

Pages