UNDERSTANDING AND MEASURING COMPRESSION RATIOS
Since race pistons in domestic V8 engines move up and down in excess of 100 times per second, replacing them is a normal part of the racer’s routine.
NHRA Top Fuel and Funny car teams replace them after every race pass and every second qualifying pass. Pro Stock teams replace them after every 40 passes approximately, and weekend warriors replace them every 12 to 18 months, sooner if their engines are nitrous-assisted. At piston replacement time questions of spec changes usually arise—especially the topic of compression ratios.
Diamond Piston’s Ron Beaubien explains, “An engine’s compression ratio is calculated by taking the total swept volume (with the piston at bottom dead center) and dividing it by the total compressed volume (with the piston at top dead center). For example, if the total swept volume of a 632cu in big-block Chevrolet is 1380.34cc (cubic centimeters) and the total compressed volume is 86.69cc the compression ratio would be stated as15.92:1.”
NHRA Top Fuel and Funny car teams replace them after every race pass and every second qualifying pass. Pro Stock teams replace them after every 40 passes approximately, and weekend warriors replace them every 12 to 18 months, sooner if their engines are nitrous-assisted. At piston replacement time questions of spec changes usually arise—especially the topic of compression ratios.
Diamond Piston’s Ron Beaubien explains, “An engine’s compression ratio is calculated by taking the total swept volume (with the piston at bottom dead center) and dividing it by the total compressed volume (with the piston at top dead center). For example, if the total swept volume of a 632cu in big-block Chevrolet is 1380.34cc (cubic centimeters) and the total compressed volume is 86.69cc the compression ratio would be stated as15.92:1.”
To find the engine’s total swept area in cubic inches the following formula can be applied: 0.7854 x bore diameter x bore diameter x stroke length x the number of cylinders. To convert cubic inches to cubic centimeters multiply by 16.39. Using a burette is the best method of measuring the compressed volume (chamber volume plus piston volume).
Compression ratios are often influenced by rule book regulations. Also engine efficiency is a deciding element in their composition. Higher compression ratios are not always the ones best calculated to succeed. When you over-compress the cylinder you induce a ‘pumping loss’—it takes horsepower to squeeze the cylinder’s contents.
Keith Wilson of Wilson Manifolds, who for thirty years has distinguished himself with the leading racing teams in attaining better air-fuel distribution and cylinder filling, comments, “Efficient cylinder filling allows us to keep the piston crowns as flat as possible—we try not to shoot our fire over the hillock! “Also,” says the Fort Lauderdale induction specialist, “when you examine an intake port of an assembled motor with valves adjusted, cam degreed etc., and you observe the intake valve cracked open, it is imperative the mixture flows out and around the valve rapidly into the cylinder during those early moments of valve lift. The incoming air mixture must not be impeded by an awkward shape on the piston. Any encumbrance will harm the engine’s ability to produce power.”
In addition, overly zealous ignition timing is not always recommended either. As Chuck Lawrence of Jon Kaase Racing Engines contends, “Earlier firing of the ignition causes the engine to work harder, as the piston is rising on its compression stroke it has to overcome the premature downward forces of the expanding gases.”
Calculating compression ratios accurately is important for at least three reasons. “First,” says Bob Fox, head of Diamond, “pistons are often requested with compression ratios higher than are physically possible to provide. Second, some sanctioning bodies stipulate strict limitations on compression ratios, and if they are not calculated precisely the racer could either squander power he could legitimately generate or unwittingly get caught cheating. Third, if the race engine is designed to meet strict specifications, including operating on a specific race fuel, having the compression ratio calculated properly is worth doing.”
Chamber volume is measured by inverting the cylinder head on the workbench (complete with two valves and a spark plug installed), placing a piece of thick acrylic plastic (with a 1/4in or 3/8in diameter hole in it) over the combustion chamber, filling a 100-milliliter burette graduated in cc’s with a colored liquid and transferring the liquid to the combustion chamber. This measuring process is duplicated to establish the piston volume.
Block deck height is measured from the crankshaft centerline to the block deck, usually with some form of caliper. Knowing the exact block deck height is crucial because it is used to verify four vital measurements: half of the stroke dimension, rod length, compression height, and the piston-to-deck dimension.
The piston-to-deck dimension is the measurement from the flat of the piston to the deck surface—is it to be positioned at zero (flush with the block deck surface) or placed down the bore by a small amount? Most engine builders request the piston-to-deck dimension to be .005in or .010in down the bore. This small fudge factor gives them the ability to take a skim cut off the decks at a later date if needed.
The compression height of the piston, also known as compression distance, is measured from the centerline of the piston pin to the flat on the top of the piston. Once these dimensions are established accurately the piston will be positioned at the precise height in the cylinder and the compression ratio will be exactly as desired.
However, when some of these vital dimensions are omitted—perhaps the spaces are left blank or they contain the word Stock—grief usually follows.
Let’s assume the racer has a desired compression ratio of 11.9:1 and assumes the block deck height to be stock. Let’s further assume 10.720in represents stock. But at sometime in the past, and unknown to the present owner, the block had visited a machine shop where the decks were ‘cleaned up’ and the height is, in fact, 10.700in and not 10.720in. As a result, the .020in difference in compression distance will cause the piston to sit higher in the bore, resulting in a much higher and unwanted compression ratio of around 12.5:1.
Savvy piston makers with experience in different race engine categories will tell you that compression is a most intriguing topic—and that having more is not always to your advantage. “When better cylinder head and induction manifold designs prevail,” says Bob Fox, “less compression is needed because they accomplish better cylinder filling. Therefore, it compresses more air in a given area. But if the cylinder head and the induction system are less efficient, more compression is needed because there is less air in the cylinder.”
The question then becomes, how much air are we drawing into the cylinder? But in the meantime, here is how to provide Diamond and other piston makers the vital information often missing from the piston order form.
Sources
Diamond Pistons
23003 Diamond Drive,
Clinton Township, MI 48035
Toll Free (877) 552-2112
www.DiamondRacing.net
Jon Kaase Racing Engines, Inc.
735 West Winder Ind. Parkway,
Winder, GA 30680
(770) 307-0241
www.JonKaaseRacingEngines.com
Wilson Manifolds
4700 N.E. 11th Avenue,
Oakland Park,
Florida 33334
(954) 771-6216
www.WilsonManifolds.com
Ernie Elliott Inc
2367 Elliott Family Parkway 3,
Dawsonville,
GA 30534
(706) 265-1346